Jackson’s have both ready-made frames and bespoke custom frames. The ready-made frames are available in different depths and finishes with choices for canvas, panel, and work on paper; the bespoke frames are available in a larger selection of moulding shapes and colours and are cut to your custom size for self-assembly. Here, we show you how to choose the best picture frame hanging hardware for your framed painting and how to attach it to the frame.
How to Choose Picture Frame Hanging Hardware
If you are framing a painting yourself, you will need to choose the style of frame for your work and mount your painting in it. After that, you need to decide what kind of hardware you would like on the back to enable the framed painting to be hung on the wall or on a gallery cable hanging system or from a picture rail. The requirements of where it will be hung and the size and weight of the framed painting are the main considerations.
Jackson’s ready-made frames come with all the hardware for mounting your work into the frame and two D-rings, screws, and cord for hanging it. If you ordered a bespoke size, self-assembly frame, you will need to purchase these fixings separately. They can be ordered with the frame pieces at the bottom of the Frame Builder page.
To help you decide which fixings to choose, consider how it will be hung on the wall and the size and weight of the artwork.
Hardware for Work to Hang From a Gallery Cable System
If the painting is going into a show, they will usually give information about framing and specify what hanging hardware is needed. For example, if the venue for the exhibition uses a hanging system with hooks on cables suspended from a rail, they will likely ask for D-rings, attached vertically, one on each side, often 10 cm from the top. This is low enough to ensure that the hook doesn’t show above the frame but high enough that the frame tilts forward as little as possible. The hooks at the end of the suspended cords will hook into the D-rings. Then your only decision is whether to use single or double D-rings. The term single, double, and triple here means how many screws are used to attach each D-ring to the wood: one, two, or three.
Single D-rings are appropriate for most small and medium-sized work. If the work is large and heavy, then double or even triple D-rings would be able to hold the extra weight. There are even heavy-duty D-rings with straps, which have a different sort of loop that has a very high resistance to opening under load, for extra security with heavy artwork. Though the weak element in a D-ring is usually the screw pulling out of the wood, rather than the ring expanding. All of these are screwed in vertically with the D-ring towards the top of the artwork. The square open sawtooth hangers also work well for hanging from gallery hooks on cables.

It is hard to specify the weight that a D-ring can hold because much depends on the screws and the softness of the wood and whether a narrow pilot hole was drilled (this makes it stronger because it is less likely to split the wood). It also depends on the angle of gravitational force caused by the cord across the work (see more below on how to reduce this tension by using two screws or wall hooks). But this method, of two vertical D-rings and no cord, where the D-rings hook directly onto hooks or screws in the wall or on hooks hanging from cables, is the strongest method for hanging work. See more about this in the next section on hanging with a cord.
You will usually want to use two D-rings for either a portrait format or a landscape format; you don’t usually put one in the centre at the top. That is because a lone D-ring isn’t as strong and the weight should not be on the top bar – it could cause the sides of the frame to pull apart from the weight below. If the frame moulding is narrow, the ring also may be visible above the edge. Using two D-rings also helps to keep the artwork level. If the hanging rail system doesn’t have enough hooks and cables and you need to use only one, the solution is often to stretch a cord across the back and hang the cord on the single cable hook. If you aren’t sure of the hanger requirements, contact the show organiser, they may have specific requirements for the picture frame hanging hardware.





Using D-rings With a Wire or Cord is Versatile and Professional
In addition to a gallery cable hanging system, D-rings facing upwards can also be used for home display with two hooks or long protruding screws on the wall. This is a good choice for paintings that are either very large or very wide, because the tension on a cord stretched that far apart can pull the screws out. It is best to hang the work with the wall hooks or screws directly in the D-rings or straps. But if you are adding cord or picture wire stretched between the D-rings, then it is usual for the D-rings to be attached horizontally, facing inwards.

Using D-rings facing inwards with wire or cord stretched between them is a versatile solution because the work can be hung on many different wall hangers. It can be hung with a single hook of a gallery hook-and-cable hanging system on the cord across the back or on two gallery cable hooks through the two D-rings, even though they are facing inwards. It can also be hung by the cord on a screw or two screws in the wall or from a picture hook, or two picture hooks in the wall. So you are covered for most contingencies.
Using D-rings with a wire or cord across is also a good choice if you are selling framed artwork, as it will be suitable for most situations in a collector’s home and is often how professionally framed artwork is presented. The white cord that we stock will hold a lot of weight, can be doubled for extra strength, and doesn’t stretch, so it will not sag.
For most paintings, using single-hole D-rings is strong enough. If you are concerned about strength because your framed work is very heavy, drilling a small pilot hole will help your screws be less likely to pull out (because the wood is less likely to split). As will using slightly longer screws, if the wood is thick enough. Double-hole D-rings or D-rings with long strap fasteners are also used for very heavy artwork.
A D-ring is usually placed 1/3 of the way down from the top of the work and either centred in the width of the wood or placed near the inside edge with the ring extended past the wood to behind the canvas. I prefer the ring to extend over the edge and that is also how our ready-made frames are prepared.
To Install D-rings:
First, check the artwork is the right way up. Then, make a mark 1/3 of the way down on each side. Then place the D-ring at that mark with the ring facing inwards and hanging over the edge. Use a bradawl to poke a hole where the screw or screws will go. If the wood is hard, you may want to drill a small pilot hole for the screw to prevent the wood cracking when you screw in the screw. Check the length of your screw, it should be about half the depth of the wood. The flat side of the D-ring band is usually flat to the wood, to allow the D-ring to move as it will shift if used with cord or wire stretched across, as the cord will be pulling it upwards. Screw the screw in firmly but not overly tight.
To Install the Picture Cord:
While there are other ways to tie the cord that stretches between the D-rings, I prefer to thread the method that I learned from a framer years ago. It is fast, simple and the double cord is strong. You thread the middle of the cord through one ring and tie a larks head knot, then pull the doubled cord across and tie a knot around the other D-ring and an over-under-over series of knots around the cord, similar to doing macrame. The cord should be a bit slack (more about that below). Then trim the end and tape it down. Doing the tie to one side means that there won’t be a lump of knots to interfere with either one or two wall hooks.
Here’s an illustration of the steps:

















Which Side Up for the D-rings



How Tight the Cord Should Be Between the D-rings
Whether you are using cord or wire, keeping the cord that goes across the back a bit slack will help prevent the screws from pulling out of the wood. The more horizontal the cord, the more tension on the screws in the D-ring. The force of the weight of the painting can end up being multiplied threefold. So a little bit of slack helps with this. Another way to get the cord to be at an even more vertical angle is to hang the painting on two screws or hooks spaced a bit apart. The angle of the cord coming up from the D-rings is more vertical which reduces the strain on the D-rings. This is another reason for a slack cord, so that it can fit across two screws.


Open Square Sawtooth Hangers
These are meant for a frame with an open back, like a stretched canvas, not a flush back like a watercolour with a backing board, because there needs to be some space behind this fixing. One can be used at the top centre on small portrait format frames, while two are used for horizontal format frames or heavier work. The work can then be hung on the wall with nails, screws, wall hooks, and cable hooks.
These hangers have four benefits. One, the central square can fit over a large picture hook, with the micro sawtooth ridges that are on the bottom bar, sitting on the hook and the body of the hook fitting inside the square. The frame can sit flush against the wall because the large hook sits through the square inside the stretched canvas space. Two, because the screw holes are slots, the hangers can be adjusted by a few millimeters to make the work hang level. This is super helpful if you are hanging a show yourself. If you find that your artworks are a little bit crooked, rather than screwing new holes in the wall, you can loosen the screws on the back a few turns and slide the squares up or down a bit and re-tighten. Three, they are wide enough to allow you to slide the picture to the left or the right on the wall screws, allowing you to adjust your spacing a bit. Lastly, when you sit the sawtooth square onto your wall fixing, the little saw teeth help stabilize the work and it doesn’t tilt easily over time. You can also string cord between the squares, if needed in an emergency, so they are versatile.





Mirror Plates to Keep Work Safely Attached to the Wall
Where work might get knocked either off the wall or into a crooked position or where the art is left unattended, mirror plates can add some security. It can also be a convenient way to hang a lot of work along a central line. Pick the central eyeline you’d like to use, often 57 inches from the ground, and mark this line around the room, with either pencil that you will later erase or with masking tape. Then mark all the frames on the back in the centre of the sides. Attach two mirror plates with the two screw holes on the back of the frame, centred over your mark with the single hole part hanging past the edge. Then screw the centre hole on each side into the wall along the marked eyeline. The brass colour can be left or disguised by painting wall paint over the mirror plate and screw.




Two Lightweight Picture Frame Hanging Hardware Solutions: Sawtooth Hanger and Screw Eyes
For a very lightweight painting, a simple solution is to use a single-bar sawtooth hanger. This is attached at the top centre of the back of the frame with two small nails or very small screws. The work can then be hung on a nail, screw, or picture hook in the wall.

Another hanging hardware choice for a lightweight painting is to use two screw eyes with cord across. These can be attached to stick out from the back. Or if you are good with fiddly things, they can be attached from the inside edge of the frame pointing towards the centre. Because there is little room to manoeuvre, and you need needle-nosed pliers to grip the screw eye, it can be a bit fiddly – getting it to grip the wood takes some effort, and screwing it in requires lots of short, little turns. But it is a bit tidier because it allows the frame to sit flush against the wall. Choose the size of your screw eye by checking the length of the screw part against the depth of the wood of the frame. The screw should go about halfway through.



Wall Hanging Hardware
There are a variety of hooks that can be attached to the wall with nails. You can use one or two for each painting. Long screws that are left partially sticking out are more common than wall hooks for artist-organised shows. For heavy work, the screw may be used with a wall anchor. You can use one or two screws per artwork, hanging the work either from a cord across the back or hanging vertical D-rings directly onto the screws or hooks. The ones you choose will be determined by the material the wall is made of and the size of holes you are allowed to make in them.

Picture Rail Hooks
If the work will be hanging in a house that has picture rail moulding around the top of the room, you may wish to use a picture rail hook for your wall fixing. It simply fits over the top of the deep curve of the rail moulding and the weight of the artwork will pull it enough to keep it tight.

Professional Best Practice in Picture Framing
The methods described above are for artists who wish to frame their own work for display in an exhibition or their home, to give as a gift, or to keep costs down when selling framed work. The nature of cost-saving DIY is such that you may not be observing all the best practices of professional framers. Picture framing professionals may take into account a number of other considerations that help make the frame and the artwork last longer. They may put bumper dots made of felt, cork, or rubber on the two bottom corners of the back of the frame. This is to ensure the frame rests with less of a tilt against the wall, stays in place a bit more, and doesn’t mark the wall. But also, more importantly, allows the right amount of air circulation behind the frame to prevent mould.
Picture framers may tape a layer of brown paper over the back to prevent dust getting in from behind. If the work in on paper under glass and has a few layers (mount, artwork, backing paper, backing board), they work to make sure that the structure of layers under glass can expand with humidity changes, by not being too tight on the front or the sides, but that it is sealed well enough so as not get too humid. They also know a lot about ensuring that the hardware doesn’t fail for heavy artwork. With that said, if you need to be economical, you should still be able to do an adequate job of framing your work yourself.

Further Reading
Choosing the Right Frame for Your Artwork
How to Assemble Jackson’s Bespoke Frames
How to Mount Artwork in a Frame
How to Frame a Watercolour Painting (coming soon)
Shop Framing on jacksonsart.com


2 thoughts on “How to Choose Picture Frame Hanging Hardware”
Should I put a dust cover on the back of a
gallery wrapped canvas oil painting 8×10
inches?
Hi Betty.
It would be a professional finish that many framers would do. But some professional framers don’t like to do it. Framers also vary in the material they use (cardboard or paper) and how they attach it (staple, double-sided tape, or glue). So it is up to you.
Comments are closed.